Plumbing Basics: The First Step for When Installing a Bathtub
Plumbing Basics: The First Step for When Installing a Bathtub
Blog Article
What are your opinions on A Step-by-Step Guide to Installing a Bathtub?
Mounting a bathtub isn't exactly rocket science, however it does require solid plumbing, woodworking, as well as occasionally, tiling abilities. Replacing an old bathtub with a brand-new one is also a moderately difficult job. If the old bathtub is easily accessible, the job can move quickly; if you have to open up a wall surface to eliminate the old bathtub and place the new bath tub, the task is much harder. In either case, the task is within a home handyman's abilities, although you will certainly need an assistant to vacate the old tub and embeded in the brand-new one. Ensure you have certified yourself for the task and also are comfortable trying it. Instead of hiring a contractor to take over a halfway-completed job, it is far better to take into consideration using one prior to you start. Chances are you might need a specialist plumber to make tube connections.
This write-up will certainly aid you mount a new bathtub in your bathroom if you have actually currently purchased a new bathtub and do not need to change the arrangement of your previous water pipes.
Your tools as well as product checklist must comprise the following:
Removing Old Taps
If you require to change old faucets with new ones as a part of your setup, after that the first thing you need to do is detach the water supply. After doing so, switch on the taps to drain any type of water remaining in the system. The procedure of eliminating the existing faucets can be quite bothersome because of the limited gain access to that is typically the instance.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipelines to the faucets. Have a towel prepared for the continuing to be water that will certainly originate from the pipes. As soon as the supply pipelines have been removed, utilize the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the solitary faucets from turning throughout this process. Once the taps have been removed, the holes in the bath/basin will need to be cleaned up of any old securing substance.
Prior to moving on to fit the brand-new taps, contrast the pipe connections on the old faucets to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic port to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet and the other end supplies a link to the current supply pipes.
If you need to fit a monobloc, after that you will need reducing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, position the faucet in the mounting opening in the bath/basin guaranteeing that the washers are in location in between the tap and the sink. Protect the tap in place with the maker offered backnut. When the tap is securely in place, the supply pipes can be attached to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with regular faucet ports. The previous kind needs to be linked to the tap ends initially, tightening only by hand. The supply pipelines can later on be attached to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Setting up the Bathtub
Making use of the two wood boards under its feet, put the tub in the needed setting. The wood boards are handy in uniformly spreading out the weight of the bath tub over the location of the boards rather than focusing all the weight onto four small points.
The next goal is to guarantee that the bathtub is leveled all round. This can be accomplished by inspecting the level as well as changing the feet on the tub up until the level checks out level.
To set up faucets, fit the bottom of the outermost adaptable faucet adapter to the appropriate supply pipeline by making a compression join; after that do the same for the other tap.
Activate the water supply and also check all joints as well as new pipework for leaks as well as tighten them if essential. Load the bath tub and also examine the overflow outlet and the regular outlet for leaks.
Finally, take care of the bathroom paneling as explained in the producer's user's manual. Tiling and securing around the bath tub needs to wait up until the tub has been utilized at least when as this will certainly settle it right into its last position.
Planning for the Setup
Firstly, the supporting structure provided with the bath needs to be fitted (if required) according to the producer's directions. Next, fit the faucets or mixer to the tub. When suitable the tap block, it is essential to make certain that if the tap features a plastic washing machine, it is fitted in between the bath as well as the faucets. On a plastic bath, it is also reasonable to fit a sustaining plate under the faucets unit to avoid stress on the bath tub.
Fit the adaptable faucet ports to the bottom of the two faucets making use of 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bath. Use the nut provided by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. Make sure you utilize all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bath must now prepare to be suited its final position.
Tiling Around the Tub
In the area where the bath fulfills the ceramic tile, it is required to secure the joins with a silicone rubber caulking. This is important as the fitting can relocate enough to crack a stiff seal, causing the water to permeate the wall surface in between the bath as well as the tiling, causing difficulties with dampness as well as feasible leakages to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your components and also installations. They are sold in tubes and also cartridges, as well as can securing gaps up to a width of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with twists of soaked newspaper or soft rope. Bear in mind to constantly load the bath tub with water prior to sealing, to enable the movement experienced when the tub is in usage. The sealant can fracture fairly early if you do not think about this movement prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are also easily readily available on the marketplace. It is recommended to fit the floor tiles using waterproof or water resistant sticky and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm just very drawn to A Step-by-Step Guide to Installing a Bathtub and I am praying you enjoyed my entry. Sharing is good. You just don't know, you could be helping someone out. I treasure reading our article about Tools You Need to Install a New Bathtub .
Quality assured, call! Report this page